Share
Pin
Tweet
Send
Share
Send
For the manufacture of gum will need materials:
- satin ribbons 2.5 cm wide dark and light pink.
- scissors.
- glue gun.
- a needle with a thread in the color of the ribbons.
- satin ribbon 1 cm wide in green.
- elastic for medium hair.
Three shiny beads.
- two wooden balls with a large hole.
- a large needle for ribbons with a big eye.
- a bit of dense fabric to match the colors.
- lighter.
The decoration consists of two roses with a diameter of 5 cm and two buds hanging on cords, and they are 3 cm in diameter. Let's start with the bud. We take a satin ribbon of dark pink color and cut 5 strips of 5 cm. But the green ribbons we take 4 strips of 5 cm. And for the cord we cut 30 cm. For it, you can use a ribbon of 0.5 cm wide.
Take a pink strip, lay it out in length, face down. We bend a little of the upper edge onto ourselves, press it with a needle. Now we need a large needle, we place it on the upper corner with a hem, at an angle of 45 degrees.
And starting from the very corner, scroll the tape over the needle until the upper twist angle is in the middle of the strip. We take out a large needle, and a small one in the color of the ribbon, we fix the twisting along the lower edge with small stitches. In the opposite corner we do the same twist.
Pulling the thread, slightly connect the resulting two bundles to each other, fix it.
We unfold the resulting petal on the front side and straighten it a little.
In this way we sew 4 petals for a rosebud.
Twist the fifth petal differently. We have a strip along the length from the wrong side. And the upper edge is bent to itself along the entire diagonal of the strip.
And we do the twisting along the entire length, and we fix the resulting tube.
We use such a tube-shaped blank as the base-middle of the flower. And with a needle and thread we begin the assembly of the bud. We attach one petal to the center and fix it.
Alternately, we continue to connect the petals, arranging them in a circle, we fix with a needle and thread.
But do not forget that our jewelry has two buds.
Now we begin work on roses. For one flower, we take ribbons of 2.5 cm, but you will need 10 pieces of 5 cm long, 5 pieces of a dark and light shade of pink. We twist them similarly to the petals for buds. The middle tube is made dark.
We begin the assembly. We will use the tube and 4 petals of a dark shade first. And then we sew the remaining light petals.
In this way, two roses turned out.
The time has come for green ribbons. For two buds, the mode is 8 strips 5 cm long. And for two roses there will be 8 pieces of 6 cm each. First, we make separate leaves in the kanzashi style. Take a strip and fold in half, with the front side inside.
We place the fold of the strip on the left side of ourselves, and begin to cut on the right side. We start from the bottom corner, directing to the opposite top corner, not reaching the bend of 3 mm. And this section is connected using a lighter.
We turn it on the front side and get a little bag with a small hole in the bottom corner.
Now we fix 4 leaves together for the bottom of the bag with a thread in the color of the ribbon.
And on the wrong side, we sew the side edges of the bundles of adjacent leaves.
It turns out a workpiece stitched in the middle on the wrong side and with four sharp corners.
We take the bud and connect it to the leaf blank with a thread, leave a tail on the front side for further work.
We also make a lace for the bud. Take a thin ribbon 30 cm long and a wooden bead.
With a needle for ribbons, wrap the bead with a green ribbon, leave two tails in the same direction.
Alternately, we twist each remaining ribbon in one direction with our fingers. Then we connect both twists together, we relax a little and they twist together with each other, make a beautiful tourniquet.
Sew this blank to the bud with the leaves left by the thread. Now the bud on the cord is completely ready, but do not forget that we have two buds.
Now we take an elastic band for hair and we sew to it a small strip of dense red fabric.
For complete assembly of the decoration, all the blanks are assembled. It remains to add 2 circles of thick red fabric with a diameter of 3.5 cm. And three more shiny beads, as well as several triangles cut from the green ribbon for the leaves.
Let's start the assembly. We take one red circle and we attach two buds to the edges of the cords with a glue gun to it. And the bonding places are closed with green corners.
Then we glue two roses, directing them from each other. Buds should hang, on the one hand, between these roses. And in the interval between the roses, we glue 3 shiny beads.
Gum with a strip glue to the second red circle. And it remains only to connect both circles - the foundations together.
And on this our decoration is ready. Good luck to all.
Share
Pin
Tweet
Send
Share
Send